These Calibration and Sanding Disks are a real time saver for aligning a saw. They are precision ground extra thick for absolute balance and flatness. Simply mount the disk onto the saw and align the disk with a square. Because there are no teeth to get in the way, it will produce a more accurate reading. Then simply remove the disk and mount your blade. Freud Disks will also turn your table saw into a disk sander. Simply mount any of the adhesive backed Freud Sanding Disks (4 popular grits available) onto the Freud Calibration and Sanding Disk and use as a disk sander. Sanding time will be cut down to practically nothing. These disks will save you time and money.

Kit includes the 4911 Deluxe Miter Gauge, 4424 24" Ultra Track, 4424F 24" Fence Face, 4824 24" Ruler Bar, 3724R 24" Tape, 4516 & 4519 Flip Stops, 4523 Micro Adjuster, 4575 Track Stop and 950 MiterMatic.
4824 & 3724: 24" Ruler Bar & Tape mounts to the back of the 4424 Ultra Track fence and makes positioning our 4516 or 4519 Flip Stop easy.
4516 Curved Flip Stops unique arm auto-lifts when stock up to 7/8" thick is pushed against it. 4519 Straight Flip Stop is compact and light.
4523 Micro Adjuster mounts to the top of the Ultra Track and a 4516 or 4519 to fine tune the Flip Stops position.
4575 Track Stop can be used as a rigid stop for cut-off work or a relocation device (back mount) when you need to remove the Ultra Track from the miter gauge and then reinstall it in the same position.
950 MiterMatic provides a way to set all the unusual angles not provided for in the angle settings of the Deluxe Miter Gauge. Simple, foolproof and easy to use!

The Kreg Precision Miter Gauge System has a number of unique features that make it stand out from all the rest. Its factory calibrated accuracy starts with a gauge head that is machined on a computerized milling machine for absolute precision. An easy-to-read Vernier scale allows precise angle adjustments up to 1/10th of a degree. Five patented bar adjusters take up the play in the miter slot for a perfect fit. A 24" fence section with patented Flipstop and self-adhesive measuring tape is also included. Factory calibrated so it is perfect right out of the box Positive stops at 0, 10, 22-1/2, 30, and 45 degrees Brass pin allows quick changes between positive stop angles 24" bar with 5 bar adjusters eliminates the play between the bar and the miter slot

BOSCH POWER TOOLS Replacement Part 2610997204 Miter Gauge Assembly

Reads Upside down! Measurements invert when cube is rotated! Measure absolute level and relative bevel with one device! Super large clear crystal display makes digital angle measurements very easy to read. Chrome-finished alloy body contains strong magnets on the bottom and both sides for maximum versatility. Great for measuring saw blade angles relative to your table! Requires one 9V battery. Please Note: Due to shipping restrictions, this item can only be shipped within the United States via ground transportation (cannot be shipped international). This item cannot be shipped by air, priority delivery services, through the postal system or sent to a post office box address

Wide applications in monitoring environmental conditions.

• Displays wet bulb, dew point, humidity and temperature
• No twirling or charts necessary
• Large digital display
• Dew point measurement
• Wet & dry bulb temperature
• Min/max memory with reset key
• F or C readings
• Data hold
• Auto power off
• Low battery indication
• Microprocessor based design

Includes:
• Protective Cap with Pocket Clip
• Batteries

Product Dimensions:
Length (in): 6.7 Weight (lbs):
Width (in): 1.85
Height (in): 0.5
Specifications:
Temp. range: -4 to 122F (-20 to 50C)
Humidity range: 0 to 100% RH
Dew point: -22 to 122F (-30 to 50C)
Temp. accuracy: ±1.8F (±1C)
Humidity accuracy: ±5% of reading
Response time: 60 seconds (approx.)
Dimensions: 6.7" x 1.85" x 0.5"
Power source: 2 "AAA" battery

This digital readout kit can be adapted to a number of woodworking machines, including router lifts, router tables, planers and shapers. It has a remote display connected with a 3 ft. cord that can be disconnected for easy installation and access. The large easy to read display reads in inches with fractions (1.64") or millimeters. Decimal inches are displayed in .001" increments and millimeters in .05mm increments. Fits router lifts made by Jessem, Jointech, and others. The readout can be easily installed using magnets, double face tape, or screws. Vertical and horizontal slider mounting hardware is included.

The Dixie Digital Angle Gauge is used to check or set angles on your saw blades, bits, fences and machine tops. Three powerful built in magnets hold securely to steel tables or fences 9even bandsaw blades) Fast, accurate reading from 0 to 180 degrees. Use on table saw, bandsaw, drill press or miter saw.